Dell G3 3500 Service Manual Download

Page: 52 / 79

Installing the power button with fingerprint reader

Prerequisites

If your are replacing a component, remove the existing component before performing the installation procedure.

Steps

1. Locate the power button with fingerprint reader slot on your computer.

2. Align and place the power button with fingerprint reader on the palm-rest and keyboard assembly.
3. Replace the two screws (M2x3) that secure the power button with fingerprint reader to the palm-rest and keyboard assembly.

Next steps

1. Install the

2. Install the

3. Install the

4. Install the

5. Install the

6. Install the

7. Install the

8. Install the

solid-state drive in M.2 slot two

9. Install the

solid-state drive in M.2 slot one

10. Install the

WLAN card

11. Install the

memory module

12. Install the

base cover

13. Follow the procedure in

After working inside your computer

Removing and installing components

Summary of Contents for G3 3500
















































































Search results

Summary of Contents for G3 3500

Reviews:

Related manuals for G3 3500

Brands by name

Popular brands

Dell G3 3500, Service Manual

Search results

Summary of Contents for G3 3500

Reviews:

Related manuals for G3 3500

Brands by name

Popular brands