Dell G3 15 3500 Service Manual Download

Page: 36 / 75

Speakers

Removing the speakers

Prerequisites

1. Follow the procedure in

Before working inside your computer

2. Remove the

base cover

About this task

The following image indicates the location of the speakers and provides a visual representation of the removal procedure.

Steps

1. Disconnect the speaker cable from the system board.
2. Note the routing of the speaker cable, and remove the speaker cable from the routing guides on the palm-rest and keyboard

assembly.

NOTE:

Note the position of the rubber grommets before lifting the speakers.

3. Lift the speakers, along with the cable, off the palm-rest and keyboard assembly.

Installing the speakers

Prerequisites

If your are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the speakers and provides a visual representation of the installation procedure.

Removing and installing components

Summary of Contents for G3 15 3500












































































Search results

Summary of Contents for G3 15 3500

Reviews:

Related manuals for G3 15 3500

Brands by name

Popular brands

Dell G3 15 3500, Service Manual

Search results

Summary of Contents for G3 15 3500

Reviews:

Related manuals for G3 15 3500

Brands by name

Popular brands