manualshive.com logo in svg

Dell G16 7620, Service Manual, Page: 52 / 79

Share
Download
Dell G16 7620 Service Manual Download Page 52

3. Install the 

solid-state drive

.

4. Install the 

rear cover

.

5. Install the 

battery

.

6. Install the 

base cover

.

7. Follow the procedure in 

After working inside your computer

.

USB board

Removing the USB board

Prerequisites

1. Follow the procedure in 

Before working inside your computer

.

2. Remove the 

base cover

.

3. Remove the 

battery

.

4. Remove the 

rear cover

.

5. Remove the 

solid-state drive

.

6. Remove the 

wireless card

.

7. Remove the 

system board

.

NOTE:

 The system board can be removed as an assembly with the memory modules, fan and heat-sink assembly,

ethernet and audio board, and USB board attached.

About this task

The following image indicates the location of the USB board and provides a visual representation of the removal procedure.

Steps

1. Turn the system-board assembly over.
2. Remove the two screws (M2x4) that secure the USB board to the system-board assembly.
3. Disconnect and remove USB board from the system-board assembly.

52

Removing and installing components

Summary of Contents for G16 7620
















































































Reviews:

No comments