Dell EMC VxFlex Ready Node 13G Manual Download Page 65

Page: 65 / 84

Figure 12 Example of a mixed SSD and HDD configuration

Install the DAS Cache utility in a Windows server

Install the DAS Cache utility in a Windows-based VxFlex Ready Node server.

Before you begin

Ensure that you have:

Administrator access to the server on which DAS Cache is to be installed

Internet access for downloading the DAS Cache utility

Procedure

1. Download the DAS Cache utility from EMC Online Support (

https://

support.emc.com

2. Copy the installation file to a temporary folder.

3. From the Windows console, or via RDP, install the DAS Cache utility.

4. During installation, select Enable caching for DAS in a software defined

storage environment.

Additional Configurations

Install the DAS Cache utility in a Windows server

Summary of Contents for EMC VxFlex Ready Node 13G





















































































Search results

Summary of Contents for EMC VxFlex Ready Node 13G

Reviews:

Related manuals for EMC VxFlex Ready Node 13G

Brands by name

Popular brands

Dell EMC VxFlex Ready Node 13G, Manual

Search results

Summary of Contents for EMC VxFlex Ready Node 13G

Reviews:

Related manuals for EMC VxFlex Ready Node 13G

Brands by name

Popular brands