Dell EMC VxFlex Ready Node 13G Manual Download Page 17

Page: 17 / 84

CHAPTER 2

Configuring the Hardware

The following topics describe how to configure the hardware, set BMC (iDRAC) IP
addresses, and map the ISO for servers in a VxFlex Ready Node environment.

Set up the BMC (iDRAC) IP address and BIOS

...................................................18

Verify the status of the system hardware, storage controller, and disks - 13G
servers

............................................................................................................... 20

Open the KVM console - 13G servers

..................................................................21

Updating the BIOS, firmware and settings

......................................................... 22

Configuring the Hardware

Summary of Contents for EMC VxFlex Ready Node 13G





















































































Search results

Summary of Contents for EMC VxFlex Ready Node 13G

Reviews:

Related manuals for EMC VxFlex Ready Node 13G

Brands by name

Popular brands

Dell EMC VxFlex Ready Node 13G, Manual

Search results

Summary of Contents for EMC VxFlex Ready Node 13G

Reviews:

Related manuals for EMC VxFlex Ready Node 13G

Brands by name

Popular brands