manualshive.com logo in svg

Dell E70S, Installation And Service Manual

The Dell E70S Installation and Service Manual is a comprehensive guide designed to assist users in the set-up and maintenance of their Dell E70S product. This user manual is available for free download on our website, ensuring easy access to all the necessary instructions and support for your device.

Share
Download
background image

iDRAC Quick Sync 2 indicator codes

iDRAC Quick Sync 2 module (optional) is located on the left control panel of the system.

Table 79. iDRAC Quick Sync 2 indicators and descriptions 

iDRAC Quick Sync 2 indicator

code

Condition

Corrective action

Off (default state)

Indicates that the iDRAC Quick Sync 2
feature is powered off. Press the iDRAC
Quick Sync 2 button to power on the
iDRAC Quick Sync 2 feature.

If the LED fails to power on, reseat the left
control panel flex cable and check. If the problem
persists, see the 

Getting help

 section.

Solid white

Indicates that iDRAC Quick Sync 2 is
ready to communicate. Press the iDRAC
Quick Sync 2 button to power off.

If the LED fails to power off, restart the system.
If the problem persists, see the 

Getting help

section.

Blinks white rapidly

Indicates data transfer activity.

If the indicator continues to blink indefinitely, see
the

Getting help

 section.

Blinks white slowly

Indicates that firmware update is in
progress.

If the indicator continues to blink indefinitely, see
the

Getting help

 section.

Blinks white five times rapidly
and then powers off

Indicates that the iDRAC Quick Sync 2
feature is disabled.

Check if iDRAC Quick Sync 2 feature is
configured to be disabled by iDRAC. If
the problem persists, see the 

Getting help

section. 

www.dell.com/poweredgemanuals

 or 

Dell

OpenManage Server Administrator User’s Guide

at 

https://www.dell.com/openmanagemanuals

.

Solid amber

Indicates that the system is in fail-safe
mode.

Restart the system. If the problem persists, see
the 

Getting help

 section.

Blinking amber

Indicates that the iDRAC Quick Sync 2
hardware is not responding properly.

Restart the system. If the problem persists, see
the 

Getting help

 section.

iDRAC Direct LED indicator codes

The iDRAC Direct LED indicator lights up to indicate that the port is connected and is being used as a part of the iDRAC
subsystem.

You can configure iDRAC Direct by using a USB to micro USB (type AB) cable, which you can connect to your laptop or
tablet. Cable length should not exceed 3 feet (0.91 meters). Performance could be affected by cable quality. The following table
describes iDRAC Direct activity when the iDRAC Direct port is active:

Table 80. iDRAC Direct LED indicator codes 

iDRAC Direct LED

indicator code

Condition

Solid green for two
seconds

Indicates that the laptop or tablet is connected.

Blinking green (on for
two seconds and off for
two seconds) 

Indicates that the laptop or tablet connected is recognized.

System diagnostics and indicator codes

227

Summary of Contents for E70S















































































































































































































































Reviews:

No comments

Related manuals for E70S

LaCie 5big - Network NAS Server Quick Start Manual preview
5big - Network NAS Server
Brand: LaCie Pages: 9
LaCie 2big NAS Quick Install Manual preview
2big NAS
Brand: LaCie Pages: 14
Hawking HMPS2U User Manual preview
HMPS2U
Brand: Hawking Pages: 40
Moxa Technologies NPort W2150Plus Series User Manual preview
NPort W2150Plus Series
Brand: Moxa Technologies Pages: 167
xFusion Digital Technologies FusionServer 2288 V5 Manual preview
FusionServer 2288 V5
Brand: xFusion Digital Technologies Pages: 86
xFusion Digital Technologies FusionServer 1288H V5 Technical Paper preview
FusionServer 1288H V5
Brand: xFusion Digital Technologies Pages: 96
Fusion FusionServer 2298 V5 Manual preview
FusionServer 2298 V5
Brand: Fusion Pages: 89
Rasilient AI72 User Manual preview
AI72
Brand: Rasilient Pages: 30
Supermicro AS-1010S-MR User Manual preview
AS-1010S-MR
Brand: Supermicro Pages: 96
Supermicro A+ User Manual preview
A+
Brand: Supermicro Pages: 130
Supermicro 8014T-T User Manual preview
8014T-T
Brand: Supermicro Pages: 124
3Com 3CRWPS10075-US - OfficeConnect Wireless 54Mbps 11g Print Server User Manual preview
3CRWPS10075-US - OfficeConnect Wireless 54Mbps 11g Print Server
Brand: 3Com Pages: 94
3Com CS/2500 Installation Manual preview
CS/2500
Brand: 3Com Pages: 116
Intel SE7221BA1 Technical Manual preview
SE7221BA1
Brand: Intel Pages: 77
iServer MicroServer iTHX-W Firmware Upgrade Instructions preview
MicroServer iTHX-W
Brand: iServer Pages: 5
seneye SWS Manual preview
SWS
Brand: seneye Pages: 11
easyRAID NAS easyRAID FN-420GT Operation Manual preview
easyRAID FN-420GT
Brand: easyRAID NAS Pages: 128
Raidon ST7610 User Manual preview
ST7610
Brand: Raidon Pages: 20

Brands by name

Popular brands

Load more brands