Dell E68S Page 182 Installation And Service Manual Download

Page: 182 / 194

System diagnostics and indicator codes

This section describes the diagnostic indicators on the system front panel display system status during system startup.

Topics:

•

Status LED indicators

•

System health and system ID indicator codes

•

iDRAC Quick Sync 2 indicator codes

•

iDRAC Direct LED indicator codes

•

LCD panel

•

NIC indicator codes

•

Power supply unit indicator codes

•

Drive indicator codes

•

Using system diagnostics

Status LED indicators

NOTE:

The indicators display solid amber if any error occurs.

Figure 153. Status LED indicators

Table 40. Status LED indicators and descriptions

Icon

Description

Condition

Corrective action

Drive indicator

The indicator turns solid amber if
there is a drive error.

●

Check the System Event Log to determine if the
drive has an error.

●

Run the appropriate Online Diagnostics test.
Restart the system and run embedded
diagnostics (ePSA).

●

If the drives are configured in a RAID array,
restart the system, and enter the host adapter
configuration utility program.

Temperature
indicator

The indicator turns solid amber if
the system experiences a thermal
error (for example, the ambient
temperature is out of range or
there is a fan failure).

Ensure that none of the following conditions exist:

●

A cooling fan has been removed or has failed.

●

System cover, air shroud, or back filler bracket is
removed.

●

Ambient temperature is too high.

●

External airflow is obstructed.

If the problem persists, see the

Getting help

section.

182

System diagnostics and indicator codes

Summary of Contents for E68S



































































































































































































Search results

Summary of Contents for E68S

Reviews:

Related manuals for E68S

Brands by name

Popular brands

Dell E68S, Installation And Service Manual

Search results

Summary of Contents for E68S

Reviews:

Related manuals for E68S

Brands by name

Popular brands