![Dell E67S Installation And Service Manual Download Page 68](http://html.mh-extra.com/html/dell/e67s/e67s_installation-and-service-manual_85107068.webp)
Table 15. Supported memory matrix (continued)
DIMM type
Rank
Capacity
DIMM rated
voltage and
speed
Operating Speed
1 DIMM per
channel (DPC)
2 DIMMs per
channel (DPC)
8 R
128 GB
DDR4 (1.2 V), 3200
MT/s
3200 MT/s
2933 MT/s
NOTE:
The older 32 GB capacity RDIMM memory with x4 data width and 8Gb DRAM density cannot be mixed with the
newer 32 GB capacity RDIMM memory with x8 data width and 16Gb DRAM density in the same AMD EPYC™ processor
unit.
NOTE:
The older 128 GB capacity LRDIMM memory at 2666 MT/s speed cannot be mixed with the new 128 GB capacity
LRDIMM memory at 3200 MT/s speed.
.
General memory module installation guidelines
To ensure optimal performance of your system, observe the following general guidelines when configuring your system memory.
If your system's memory configurations fail to observe these guidelines, your system might not boot, stop responding during
memory configuration, or operate with reduced memory. This section provides information on the memory population rules and
about the non-uniform memory access (NUMA) for single or dual processor system.
The memory bus may operate at speeds of 3200 MT/s, 2933 MT/s, or 2666 MT/s depending on the following factors:
●
System profile selected (for example, Performance Optimized, or Custom [can be run at high speed or lower])
●
Maximum supported DIMM speed of the processors
●
Maximum supported speed of the DIMMs
NOTE:
MT/s indicates DIMM speed in MegaTransfers per second.
The system supports Flexible Memory Configuration, enabling the system to be configured and run in any valid chipset
architectural configuration. The following are the recommended guidelines for installing memory modules:
●
All DIMMs must be DDR4.
●
Mixing of memory module capacities in a system is not supported.
●
If memory modules with different speeds are installed, they operate at the speed of the slowest installed memory module(s).
●
Populate memory module sockets only if a processor is installed.
○
For single-processor systems, sockets A1 to A16 are available.
○
For dual-processor systems, sockets A1 to A16 and sockets B1 to B16 are available.
○
In Optimizer Mode, the DRAM controllers operate independently in the 64-bit mode and provide optimized memory
performance.
Table 16. Memory population rules
Processor
Configuration
Memory population
Memory population
information
Single processor
Optimizer (Independent
channel) population order
A{1}, A{2}, A{3}, A{4}, A{5},
A{6}, A{7}, A{8}, A{9}, A{10},
A{11}, A{12}, A{13}, A{14}, A{15},
A{16}
Odd amount of DIMMs per
processor allowed.
Dual processor (Start
with processor1. Processor
1 and processor 2
population should match)
Optimizer (Independent
channel) population order
A{1}, B{1}, A{2}, B{2}, A{3}, B{3},
A{4}, B{4}, A{5}, B{5}, A{6},
B{6}, A{7}, B{7} A{8}, B{8}
Odd amount of DIMMs
per processor is allowed.
DIMMs must be populated
identically per processor.
●
Populate all the sockets with white release tabs first, followed by the black release tabs.
●
In a dual-processor configuration, the memory configuration for each processor must be identical. For example, if you
populate socket A1 for processor 1, then populate socket B1 for processor 2, and so on.
●
Unbalanced or odd memory configuration results in a performance loss and system may not identify the memory modules
being installed, so always populate memory channels identically with equal DIMMs for best performance.
68
Installing and removing system components