Dell D800 - Latitude 15.4" Notebook Service Manual Download Page 21

Page: 21 / 78

Memory Module, Mini PCI Card, Modem, and Modules: Dell Latitude D800 Service Manual

1 modem cable

2 modem

See mini RSL

3 pull-tab

4 screw

2013T

5 system board connector

NOTICE:

The cable connectors are keyed for correct insertion; do not force the

connections.

4. Connect the modem cable to the modem.

NOTICE:

To prevent damage to the modem, press the modem into the connector

directly over

the connector.

5. Align the modem with the screw hole, and press the modem into the connector directly over the

connector on the system board.

file:///I|/SERVICE%20MANUALS/DELL%20MANUALS/...de/D800/D800%20SERVICE%20MANUAL/upgrades.htm (9 of 13)6/21/2004 2:16:55 AM

Summary of Contents for D800 - Latitude 15.4" Notebook















































































Search results

Summary of Contents for D800 - Latitude 15.4" Notebook

Reviews:

Related manuals for D800 - Latitude 15.4" Notebook

Brands by name

Popular brands

Dell D800 - Latitude 15.4" Notebook, Service Manual

Search results

Summary of Contents for D800 - Latitude 15.4" Notebook

Reviews:

Related manuals for D800 - Latitude 15.4" Notebook

Brands by name

Popular brands