Dell D28M Service Manual Download Page 28 | Manualshive

Page: 28 / 94

background image

2. Disconnect the fan cable from the system board.
3. Gently pull the rubber grommets to release the fan from the chassis .
4. Remove the fan off the chassis.

Installing the chassis fan

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following images indicate the location of the chassis fan and provides a visual representation of the installation procedure.

Steps

1. Insert the rubber grommets on the chassis.
2. Align the slots on the fan with the rubber grommets on the chassis.
3. Route the rubber grommets through the slots on fan and pull the rubber grommets until the fan snaps into position.
4. Connect the fan cable to the system board.

28

Disassembly and reassembly

«
...
26
27
28
29
30
...
»

Summary of Contents for D28M































































































Reviews:

No comments

Related manuals for D28M

Brand: Acer Pages: 20

Brand: Acer Pages: 20

Brand: Acer Pages: 18

Brand: Acer Pages: 30

Brand: Raven Pages: 71

Brand: Gateway Pages: 108

Brand: Seneca Pages: 8

Brand: UMAX Technologies Pages: 34

Brand: PRESONUS Pages: 8

Brand: Walfront Pages: 39

Brand: IBASE Technology Pages: 68

7012 300 Series

Brand: IBM Pages: 148

Brand: Commodore Pages: 31

Brand: IBM Pages: 194

Brand: Zotac Pages: 20

Inspiron 22 3000 SERIES

Brand: Dell Pages: 130

Brand: Packard Bell Pages: 13

Brand: Packard Bell Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands