Dell Aurora R6 Service Manual Download Page 93

Page: 93 / 164

Replacing the wireless card

WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in

Before working inside your computer

. After working inside your

computer, follow the instructions in

After working inside your

computer

. For more safety best practices, see the Regulatory

Compliance home page at

www.dell.com/regulatory_compliance

Procedure

CAUTION: To avoid damaging the wireless card, do not place any
cables under it.

Align the notch on the wireless card with the tab on the wireless-card slot.

Slide the wireless card at an angle into the wireless-card slot.

Connect the antenna cables to the wireless card.
The following table provides the antenna-cable color scheme for the
wireless card supported by your computer.

Table 3. Antenna-cable color scheme

Connectors on the wireless card

Antenna-cable color

Main (white triangle)

White

Auxiliary (black triangle)

Black

Place the wireless-card bracket on the wireless card.

Summary of Contents for Aurora R6





































































































































































Search results

Summary of Contents for Aurora R6

Reviews:

Related manuals for Aurora R6

Brands by name

Popular brands

Dell Aurora R6, Service Manual

Search results

Summary of Contents for Aurora R6

Reviews:

Related manuals for Aurora R6

Brands by name

Popular brands