Dell Alienware m17 Service Manual Download

Page: 48 / 119

Replacing the coin-cell battery

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/

regulatory_compliance

Procedure

1. Adhere the coin-cell battery to the palm-rest assembly.
2. Adhere the tape that secures the coin-cell battery cable to the palm-rest assembly.
3. Connect the coin-cell battery cable to the system board.

Post-requisites

Replace the

base cover

Replacing the coin-cell battery

Summary of Contents for Alienware m17
























































































































Search results

Summary of Contents for Alienware m17

Reviews:

Related manuals for Alienware m17

Brands by name

Popular brands

Dell Alienware m17, Service Manual

Search results

Summary of Contents for Alienware m17

Reviews:

Related manuals for Alienware m17

Brands by name

Popular brands