manualshive.com logo in svg

Dell Alienware m17 R2, Service Manual, Page: 15 / 70

Share
Download
Dell Alienware m17 R2 Service Manual Download Page 15

Installing the M.2 2230 solid-state drive

Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

NOTE: This procedure applies if you are installing a M.2 2230 solid-state drive.

NOTE: Depending on the configuration ordered your computer may have up to two M.2 cards installed. Supported card
configurations per M.2 card slot:

• M.2 2230 solid-state drive + 2230 mounting bracket
• M.2 2280 solid-state drive

NOTE: For PCIe, NVMe solid-state drives a thermal shield is required for optimal heat dissipation and is installed in the
computer when these configurations are ordered. If these configurations are installed After Point-of-Sale (APOS), that is,
after you purchase the computer; contact Dell support to purchase a thermal shield.

NOTE: Before replacing the M.2 card take note that there are two M.2 card slots present on your computer, for:

• the left card slot PCIe, NVMe and SATA AHCI cards are supported.
• the right card slot only PCIe, NVMe cards are supported.

The following image indicates the location of the M.2 2230 solid-state drive and provides a visual representation of the installation

procedure.

15

Summary of Contents for Alienware m17 R2







































































Reviews:

No comments