manualshive.com logo in svg

Dell Alienware m15 R3, Service Manual, Page: 39 / 81

Share
Download
Dell Alienware m15 R3 Service Manual Download Page 39

Steps
1. Open the latch and disconnect the keyboard-backlight cable from the keyboard-controller board.
2. Open the latch and disconnect the keyboard-controller board cable from the keyboard-controller board.
3. Open the latch and disconnect the keyboard cable from the keyboard-controller board.
4. Remove the two screws (M2x1.9) that secure the keyboard-controller board to the palm-rest assembly.
5. Pull on the securing tab to release the keyboard-controls board from the palm-rest assembly.
6. Using the plastic tab, pry and remove the keyboard-controller board from the palm-rest assembly.

Installing the keyboard-controller board

Prerequisites
If you are replacing a component, remove the existing component before performing the installation process.

About this task
The following image(s) indicate the location of the keyboard-controller board and provides a visual representation of the installation

procedure.

39

Summary of Contents for Alienware m15 R3


















































































Reviews:

No comments