manualshive.com logo in svg

Dell Alienware m15 R3, Service Manual, Page: 37 / 81

Share
Download
Dell Alienware m15 R3 Service Manual Download Page 37

Touchpad

Removing the touchpad

Prerequisites
1. Follow the procedure in 

Before working inside your computer

.

2. Remove the 

base cover

.

3. Remove the 

battery

.

About this task
The following image(s) indicate the location of the touchpad and provides a visual representation of the removal procedure.

Steps
1. Open the latch and disconnect the keyboard-controller board-cable from keyboard-controller board.
2. Lift the keyboard-controller board-cable off the palm-rest assembly.
3. Open the latch and disconnect the keyboard cable from the keyboard-controller board.
4. Fold up the keyboard cable.
5. Open the latch and disconnect the touchpad cable from the touchpad.
6. Lift the touchpad cable from the palm-rest assembly.
7. Remove the four (M2x1.9) screws that secure the touchpad to the palm-rest assembly.
8. Lift the touchpad off the palm-rest assembly.

Installing the touchpad

Prerequisites
If you are replacing a component, remove the existing component before performing the installation process.

About this task
The following image(s) indicate the location of the touchpad and provides a visual representation of the installation procedure.

37

Summary of Contents for Alienware m15 R3


















































































Reviews:

No comments