manualshive.com logo in svg

Dell Alienware 13 R3, Service Manual, Page: 74 / 78

Share
Download
Dell Alienware 13 R3 Service Manual Download Page 74

Table 5. Security tab

 

(continued)

Security

Default: Permitted

Computrace

Enable or disable the BIOS module interface of the optional

Computrace Service from Absolute Software.

Firmware TPM

UEFI Capsule Firmware Updates

Enable or disable BIOS updates through UEFI capsule update

packages.

Table 6. Boot tab

 

Boot

Boot List Option

Displays the available boot options.

File Browser Add Boot Option

Allows to add the boot options.

File Browser Del Boot Option

Allows to delete the boot options

Secure Boot

Enable or disable the secure boot feature.

Legacy Option ROMs

Enable or disable the Legacy Option ROMs.

Boot Option Priorities

Displays the boot sequence.

Boot Option #1

Displays the available first boot option.

Boot Option #2

Displays the available second boot option.

Boot Option #3

Displays the available third boot option.

Table 7. Exit tab

 

Exit

Save Changes and Reset

Allows you to exit system setup and save your changes.

Discard Changes and Reset

Allows you to exit system setup and load previous values for

all system setup options.

Restore Defaults

Allows you to restore default values for all system setup

options.

Discard Changes

Allows you to load previous values for all system setup

options.

Save Changes

Allows you to save the changes for all system setup options.

Clearing BIOS (System Setup) and System passwords

Contact Dell technical support to clear the forgotten passwords. For more information, see 

www.dell.com/contactdell

.

Clearing CMOS settings

1. Remove the 

base cover

.

2. Remove the 

wireless card

.

3. Remove the 

solid-state drive

.

4. Remove the 

rear I/O cover

.

5. Remove the 

computer base

.

6. Remove the 

battery

.

7. Remove the 

coin-cell battery

.

8. Wait for one minute.

74

Summary of Contents for Alienware 13 R3















































































Reviews:

No comments