Dell 1133 Mono Laser Page 7 User Manual Download

Page: 7 / 88

life, which indicates the average capacity
of print-outs and is designed pursuant to
ISO/IEC 19752 (See

Available supplies

The number of pages may be affected by
operating environment, printing interval,
media type, and media size. Some
amount of toner may remain in the
cartridge even when

End of life

Replace new cart

appears and the

printer stops printing.

Error

[error

number]

Turn off
then on

A systematic error has occurred

Reboot the power and try the printing job again. If
the problem persists, call for service.

Install
Toner

The toner cartridge is installed improperly,
or not installed.

Reinstall the toner cartridge two or three times to
confirm it is seated properly. If the problem persists,
the toner cartridge is not being detected. Contact the
service representatives.

Load

[media size]

[tray
number]

There is no corresponding paper in the
corresponding tray.

Load corresponding paper in the corresponding tray
(See

Loading paper in the tray

Not
Compatible
toner
cartridge

The toner cartridge is not suitable for your
machine.

Install the corresponding toner cartridge with a Dell-
genuine cartridge (See

Replacing the toner cartridge

Output bin
Full
Remove
paper

The output tray is full. Or the sensor is not
facing down.

Remove papers from the output tray, the machine
resumes printing. Or make sure the sensor is facing
down. If the problem persists, call for service.

Paper
Empty
in

[tray

number]

There is no paper in the indicated tray.

Load paper in the tray (See

Loading paper in the

tray

Pulled Out

[tray
number]

Cassette

The indicated tray cassette is not inserted,
or not properly closed.

To close the tray, lower the rear edge, align it with
the slot, and slide it into the printer.

Paper Jam
in MP Tray

Paper has jammed in the manual tray area.

Clear the jam (See

In the manual tray

Paper Jam
in Tray 1

Paper has jammed in the tray1 area.

Clear the jam (See

In tray 1

Paper Jam
inside
machine

Paper has jammed inside the machine.

Clear the jam (See

Inside the machine

Paper Jam
in exit area

Special print media has jammed in the paper
exit area.

Clear the jam.

See

In exit area

See

In the manual tray

)

Prepare
new
cartridge

Small amount of toner is left in the indicated
cartridge. The estimated cartridge life of
toner is close.

Prepare a new cartridge for a replacement. You may
temporarily increase the printing quality by
redistributing the toner (See

Redistributing toner

Remove
seal tape
&Install
Toner

The machine cannot detect a toner
cartridge.

Remove the sealing tape from the toner cartridge.
Refer to Quick Install Guide.

Replace
Toner

The toner cartridge has almost reached its
estimated cartridge life.

You can choose between

Stop

Continue

as shown

on the control panel. If you select

Stop

, the printer

stops printing and you cannot print any more without
changing the cartridge. If you select

Continue

, the

printer keeps printing but the printing quality cannot

Summary of Contents for 1133 Mono Laser

























































































Search results

Summary of Contents for 1133 Mono Laser

Reviews:

Related manuals for 1133 Mono Laser

Brands by name

Popular brands

Dell 1133 Mono Laser, User Manual

Search results

Summary of Contents for 1133 Mono Laser

Reviews:

Related manuals for 1133 Mono Laser

Brands by name

Popular brands