Dell EMC PowerEdge R7525 Installation And Service Manual Download Page 190

Page: 190 / 209

Table 68. PowerEdge R7525 Front PERC and Adapter PERC support on back planes

Front PERC

Adapter PERC

8 x 3.5 inches SAS/SATA

12 x 3.5 inches SAS/SATA

16 x 2.5 inches SAS/SATA

12 x 3.5 Rear 2 x 2.5 inches

24 x 2.5 inches (16 SAS/SATA X 2.5 8 X 2.5 inches
NVME)

12 x 3.5 Rear 2 x 2.5 inches NVME

Drive specifications

Drives

The PowerEdge R7525 system supports:

•

8 x 3.5-inch hot-swappable SAS, SATA drives.

•

8 x 2.5 inch NVMe drives.

•

12 x 3.5-inch hot-swappable SAS, SATA drives.

•

16 x 2.5-inch hot-swappable SAS, SATA drives.

•

24 x 2.5-inch hot-swappable SAS, SATA , or NVMe drives.

Backplane

•

Up to 8 x 3.5-inch SAS, SATA drives.

•

Up to 8 x 2.5 inch NVMe drives.

•

Up to 12 x 3.5-inch SAS, SATA drives.

•

Up to 16 x 2.5-inch SAS, SATA drives.

•

Up to 24 x 2.5-inch SAS, SATA , or NVMe drives.

•

Up to 2 x 2.5-inch rear SAS, SATA, or NVMe drives

NOTE:

For more information about how to hot swap NVMe PCIe SSD U.2 device, see the

Dell Express Flash NVMe PCIe

SSD User's Guide

https://www.dell.com/support

Browse all Products > Data Center Infrastructure > Storage

Adapters & Controllers > Dell PowerEdge Express Flash NVMe PCIe SSD > Documentation > Manuals and Documents.

Ports and connectors specifications

USB ports specifications

Table 69. PowerEdge R7525 system USB specifications

Front

Rear

Internal (Optional)

USB port type

No. of ports

USB port type

No. of ports

USB port type

No. of ports

USB 2.0-compliant
port

One

USB 3.0-compliant
ports

One

Internal USB 3.0-
compliant port

One

Micro-USB 2.0
compliant port

One

USB 2.0-compliant
ports

One

NOTE:

The micro USB 2.0 compliant port can only be used as an iDRAC Direct or a management port.

NOTE:

The USB 2.0 specifications provide a 5 V supply on a single wire to power connected USB devices. A unit load is

defined as 100 mA in USB 2.0, and 150 mA in USB 3.0. A device may draw a maximum of 5 unit loads (500 mA) from a
port in USB 2.0; 6 (900 mA) in USB 3.0.

NOTE:

The USB 2.0 interface can provide power to low-power peripherals but must adhere to USB specification. An

external power source is required for higher-power peripherals to function, such as external CD/DVD Drives.

190

Technical specifications

Summary of Contents for PowerEdge R7525


















































































































































































































Search results

Summary of Contents for PowerEdge R7525

Reviews:

Dell EMC PowerEdge R7525, Installation And Service Manual, Page: 190 / 209

Search results

Summary of Contents for PowerEdge R7525

Reviews: