Dell EMC G7 7590 Page 54 Service Manual Download

Page: 54 / 104

Replacing the wireless card

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

Procedure

CAUTION:

To avoid damage to the wireless card, do not place any cables under it.

1. Connect the antenna cables to the wireless card.

The following table provides the antenna-cable color scheme for the wireless card supported by your computer.

Table 2. Antenna-cable color scheme

Connectors on the wireless card

Antenna-cable color

Main (white triangle)

White

Auxiliary (black triangle)

Black

2. Align the notch on the wireless card with the tab on the wireless-card slot and insert the wireless card at an angle into the wireless-

card slot.

3. Align the screw hole of the wireless-card bracket to the screw hole on the system board.
4. Replace the screw (M2x4) that secures the wireless-card bracket to the wireless card and the system board.

Replacing the wireless card

Summary of Contents for G7 7590









































































































Search results

Summary of Contents for G7 7590

Reviews:

Related manuals for G7 7590

Brands by name

Popular brands

Dell EMC G7 7590, Service Manual

Search results

Summary of Contents for G7 7590

Reviews:

Related manuals for G7 7590

Brands by name

Popular brands