Dell EMC E68S Installation And Service Manual Download

Page: 33 / 187

Figure 23. Installing the drive backplane cover

Next steps

1. Follow the procedure listed in

After working inside your system

on page 27.

Control panel

Removing the right control panel

Prerequisites

1. Follow the safety guidelines listed in the

Safety instructions

on page 26.

2. Follow the procedure listed in the

Before working inside your system

on page 27.

Remove the drive backplane cover

4. If installed,

remove the air shroud

Remove the cooling fan assembly

Remove the side wall bracket

Steps

1. Using the Phillips #1 screwdriver, remove the screws that secure the right control panel and the right control panels cable

cover to the system and remove the cable cover away the system.

2. Disconnect the right control panel cable and the VGA cable from the connectors on the system board.
3. Holding the cable, slide the right control panel out of the system.

NOTE:

Observe the routing of the cable as you remove the right control panel from the system.

NOTE:

The numbers on the image do not depict the exact steps. The numbers are for representation of sequence.

Installing and removing system components

Summary of Contents for E68S




























































































































































































Search results

Summary of Contents for E68S

Reviews:

Related manuals for E68S

Brands by name

Popular brands

Dell EMC E68S, Installation And Service Manual

Search results

Summary of Contents for E68S

Reviews:

Related manuals for E68S

Brands by name

Popular brands