Delfa WQP12-9242B Technical & Service Manual Download Page 1

Contents

Technical Service Manual

Dishwasher

Specification                       2

Test program                       24-28

Theory of parts                    5-23

Function Description          3-4

Inspection                            29-33 

Location                                                       5

PCB                                                              6-7

Inlet valve                                                    8-10

Drain pump                                                  11-12

Heater                                                          13-14

Washing pump                                            15-16

Procedure                                                    25

Error code                                                    26-28             

Water circuit                                                3-4

Pressure switch                                          17

NTC                                                              18-19

Flowmeter                                                    20-21

Safety Hose                                                  22-23

Troubleshooting                  34-38 

                     

  

 SAFETY NOTICE

This documentation is only intended for qualified technicians 
who are aware of the respective safety regulations.

1 -

Summary of Contents for WQP12-9242B







































Reviews: