manualshive.com logo in svg

DeDietrich IX 145-110, Installation And Service Manual

Share
Download
DeDietrich IX 145-110 Installation And Service Manual Download Page 91

10.2.10  Using the fixed-speed boiler

Using the boiler according to heat input makes it possible to calibrate the 

gas valve.
The heat input corresponds to the speed of the boiler in percentage of the 

nominal output.

1. From the home screen, press the 

 and 

MENU

 keys simultaneously. 

2. Select the parameter Controller stop function by turning the 

button.

3. Press the   button to confirm.

The parameter Controller stop function On appears.

4. Press the   button to confirm. 

304:Controller stop appears.

5. Press the   button to modify the heat input value from 0 to 100 % by 

turning the 

 button. 

6. Press the   button to confirm the heat input. 

Important
Press the 

MENU

 key to return to the main display and reactivate the 

control system.

For more information, see

Setting the air/gas ratio (maximum heat input), page 61

Setting the air/gas ratio (reduced heat input), page 63

10.2.11  Selecting a heating circuit

The control panel can manage up to three different heating circuits.

1. From the home screen, turn the 

 button to select one of the three 

heating circuits available.

2. Press the   button to confirm.
3. Turn the 

 button to temporarily modify the temperature set point on 

the selected heating circuit.

4. Press the   button to confirm.

The selected heating circuit is active.

Fig.86

MW-3000085-EN-02

MENU

14:13

1.5 bar

18. February 2014
Tuesday

MENU

Fig.87

MW-3000088-EN-02

MENU

Controller stop function

On

Fig.88

MW-3000089-EN-02

MENU

80%

Adjust?

304:Controller stop function

Controller stop setpoint

0%

100%

10 Settings

7702703 - v04 - 05092019

IX

91

Summary of Contents for IX 145-110





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands