manualshive.com logo in svg

DeDietrich IX 145-110, Installation And Service Manual

Share
Download
DeDietrich IX 145-110 Installation And Service Manual Download Page 89

For more information, see

Shortcuts menu, page 73

10.2.7  Setting the domestic hot water temperature set point

1. Press the 

 key to access the shortcuts menu. 

2. Select the parameter Hot water temp setpoint by turning the 

button.

3. Press the   button to confirm.
4. Turn the 

 button to modify the temperature set point.

5. Press the   button to confirm. 

Important
Press the 

MENU

 key to return to the main display.

For more information, see

Shortcuts menu, page 73

10.2.8  Setting the room temperature set point (Reduced mode)

1. Press the 

MENU

 key to access the parameters. 

2. Select the Temps / mode CH1 menu by turning the 

 button.

3. Confirm the menu selection by pressing the   button.

The parameter Operating mode appears.

4. Select the Reduced temp setpoint menu by turning the 

 button.

5. Confirm the menu selection by pressing the   button.

The room temperature set point (Reduced mode) flashes.

6. Turn the 

 button to modify the temperature set point.

7. Press the   button to confirm. 

Important
Press the 

MENU

 key to return to the main display.

10.2.9  Programming a Holiday period

This series of functions is used to program the boiler's behaviour in holiday 

periods or during prolonged absences. The various parameters are used 

to program one of eight Holiday periods.

Important
When the function is activated, the 

 symbol is displayed.

1. Press the 

MENU

 key to access the parameters.

2. Select the Holiday heating CH1 menu by turning the 

 button.

3. Confirm the menu selection by pressing the button  .

The Select parameter appears.

Fig.80

MW-3000067-EN-03

MENU

Hot water temp setpoint

Fig.81

MW-3000070-EN-03

MENU

Reduced temp setpoint

10 Settings

7702703 - v04 - 05092019

IX

89

Summary of Contents for IX 145-110





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands