background image

 Instruction Manual 

Negative Pressure Unit green dec 

 

Version 1 

Page 60 

 

12.  Declaration of Conformity 

 

EC Declaration of Conformity acc. to Machinery Directive 2006/42 / EC Annex II 1.A 

 
The manufacturer 

deconta GmbH 
Im Geer 20 
46419 Isselburg 

hereby declares that the following product 
 
Product designation: 

green dec 

Brand:  

Serial number: 

see type plate 

Series name / Type designation: 

G 50, G 55, G 100, G 200, G 300, G 400, G 500 

Description: 

 

 

Negative pressure unit green dec 

 
complies with all applicable regulations of the above mentioned directive and the other applicable directives (hereafter), 
including the amendments applicable at the time of the declaration. The sole responsibility for issuing this Declaration 
of Conformity lies with the manufacturer. 
 
The protection objectives of the following EU directives have been complied with: 

Low Voltage Directive 2014/35 / EU 

 
The following harmonised standards were applied: 

EN 349:1993+A1:2008 

Safety of machinery – minimum gaps to avoid crushing or parts of the human body 

EN 50274:2002/AC:2009 

Low-voltage switchgear and control gear assemblies - Protection against electric 
shock - Protection against accidental direct contact with dangerous active parts  

EN 50274:2002 

Low-voltage switchgear and control gear assemblies - Protection against electric 
shock - Protection against accidental direct contact with dangerous active parts 

EN 60204-1:2006/A1:2009 

Safety of machinery - Electrical equipment of machines - Part 1: General 
requirements (IEC 60204-1: 2005 / A1: 2008) 

EN 60204-1:2006/AC:2010 

Safety of machinery - Electrical equipment of machines - Part 1: General 
requirements (IEC 60204-1: 2005 (modified)) 

EN 60335-2-69:2012 

Safety of household and similar electrical appliances  - Part 2-69: Particular 
requirements for wet and dry vacuum cleaners (IEC 60335-2-69: 2012 (modified)) 

EN ISO 13850:2015 

Machine safety - Emergency stop – Principles of design (ISO 13850: 2015) 

EN ISO 13857:2008 

Safety of machinery – Safety distances to prevent hazard zones being reached by 
upper and lower limbs (ISO 13857:2008) 

 
Name and address of the person authorised to compile the technical documentation: 
 
Krolle, Christian 
 
Place: Isselburg 
Date: 02.11..2018 
 
 
 
 
_______________________________ 
(Signature) 

Managing Director 

Summary of Contents for green dec G 100





























































Reviews: