background image

 

 

 

10)

 

With the Deck Dolly preassembled, lay the unit over the deck and align the 

bottom support brackets with the rod in the deck mount so that it hooks in. 

Depending on how it fits you may have to move the brackets to the other side of the 

Upright. The brackets have two sets of holes and the key thing to remember is that 

the wheels are close or just touching the ground when in the horizontal position. You 

can move the brackets up if needed if any interference is found. The various holes 

give you adjustability to conform to your deck. After insuring proper fit you may now 

tighten those bolts. 

 

11)

 

Once you are satisfied with the fit of the Dolly on your deck and squareness of the 

dolly you may align and tighten the lower cross support tube when the brackets are 
centered on the deck rod mount. Beginning from the bottom, tighten all bolts while 
insuring alignment. 

 

12)

 

Check all bolts for tightness before operating the Deck Dolly. 
 

13)

 

 Please take care to watch the lower deck wheels when operating the Dolly for 

the first time. You may have to raise and turn the deck anti scalping wheels so they do 

not catch on the ground. Assembly is complete. 

Using The DeckDolly 

Using the DeckDolly is a threes step process and is easy as: 

Summary of Contents for JD 1023E









Reviews: