background image

Instruction Manual

AMPLIFIERS

SPA90.2   SPA90.4   SPA150.4

SPA1000D  SPA1300D
SPA1600D  SPA1900D

• Instalation Instructions / Owners Manual •

Due to continuous improvement of the product the Specifications are subject to change without notice.

LIMITED WARRANTY

 

DB DRIVE warrants any products purchased in the U.S.A. from 

an authorized DB DRIVE dealer. All products are warranted to be free 
from  defects  in  material  and  workmanship  under  normal  use  and 
service for a period of (1) year when the unit is installed by an autho

-

rized DB DRIVE dealer. Non-authorized dealer installed products carry 
a one (1) year parts and labor limited warranty. This warranty applies to 
the original purchase only.

 

DB DRIVE will either repair or replace (as its option) any unit 

that has been found to be defective and under warranty provided the 
defect occurs within:
 
    One (1) year if purchased through an authorized DB DRIVE dealer.

 

This limited warranty does not extend to units that have been 

subjected to misuse, abuse, neglect, or accident. Products that in DB 
DRIVE’s judgment shows evidence of having been altered, modified, or 
serviced without DB DRIVE’s authorization, will be ineligible under this 
warranty.

 

To obtain warranty service please contact your retailer or see 

our web site at wwwdbdrive.net  for more details.

DB Research L.L.P. 

302 Hanmore Industrial Parkway // Harlingen, TX 78550

ph: 877.787.0101 // fx: 956.421.4513 // www.dbdrive.net

®

Summary of Contents for Speed SPA90.2









Reviews: