background image

O

P T I O N A L

  A

C C E S S O R I E S

Hardware Requirements

2

O p t i o n a l   A c c e s s o r i e s

The following optional accessories, designed for use with WeatherLink, are avail-
able from your dealer or may be ordered directly from Davis.

Telephone Modem Adapter
For transmission of data from the data logger using a modem.

Standard 4-Conductor Extension Cable
For more flexibility in the placement of your console. Add one 40’ (12 m) 
extension cable to extend the distance between your station and the computer. 
(48’ (14.4 m) maximum)

H a r d w a r e   I n s ta l l a t i o n

You can either install WeatherLink to use a direct, local connection between your 
computer and weather station, or you can install WeatherLink to use a modem 
connection to a remote weather station. Requirements and installation for each 
type of connection differ, and are explained separately below.

H a r d w a r e   R e q u i r e m e n ts

The required hardware differs depending on whether you are making a local con-
nection or a remote modem connection.

Local Connection Hardware Requirements

The following additional hardware is required for a local connection:

Computer running Windows™ 95, 98, ME, NT 4.0, 2000, or XP with at least 5 
MB of free disk space
The amount of disk space necessary depends on the archive interval. Database 
files containing data stored at a 30 minute archive interval require approxi-
mately 132K of disk space per month of data. The file size changes in a linear 
fashion depending on the archive interval. For example, data stored at a 1–
minute interval requires approximately 3.9 MB per month while the data 
stored at a 2–hour interval requires approximately 33 KB per month.

Windows-Compatible Display
VGA minimum. SVGA or High (16-bit) Color recommended.

One Free Serial Port

Remote Modem Connection Hardware Requirements

In addition to the provided hardware and the computer equipment listed above, 
the following hardware is required for a remote modem connection.

• One external modem to connect to the data logger at the remote site.

• One internal or external modem connected to your computer

• Modems must be Hayes

®

–compatible and able to send data at 1200, 2400, 

4800, 9600, or 19200 baud for use with Vantage Pro stations or at 1200 or 2400 
baud for use with a Monitor II, Wizard III, or Perception II weather station. 

WL Windows GSG content D009.fm  Page 2  Friday, September 12, 2003  12:29 PM

Summary of Contents for Perception II





















Reviews: