Datum MobileTrak5 Installation Instructions Manual Download Page 27

Page: 27 / 28

Figure 2B

Detail 2C

Page 27

MobileTrak5 Additional Rear Panel Installation

Instructions

1/4-20 FLANGE NUT

REAR PANEL WITH

TOP BRACKETS

#20 BISCUIT

1/4-20 x 1/2

PAN HD PHILLIPS

Insert a wooden biscuit joint into the rear panel that was just installed (see Detail 2C). Slide the

next rear panel into the lower channel and align the biscuit joint with the hole in the side of the

panel (see Figure 2B). Attach another set of upper brackets to the rear panel. If the system is

equipped with Datum ThinStak style shelving, the top cover will have knockouts in it to align with

the holes in upper brackets. If any shelving other than Datum ThinStak shelving is being used,

holes will need to be drilled into the top of shelving. 1/4-20 x 1/2" pan head phillips screws and

flange nuts are supplied to attach upper brackets to shelving (four per shelf). Repeat for remaining

panels.

Summary of Contents for MobileTrak5





























Search results

Summary of Contents for MobileTrak5

Reviews:

Related manuals for MobileTrak5

Brands by name

Popular brands

Datum MobileTrak5, Installation Instructions Manual

Search results

Summary of Contents for MobileTrak5

Reviews:

Related manuals for MobileTrak5

Brands by name

Popular brands