manualshive.com logo in svg

Datex-Ohmeda S/5 M-NIBP, Technical Reference Manual Slot

Share
Download
Datex-Ohmeda S/5 M-NIBP Technical Reference Manual Slot Download Page 47

APPENDIX A, Service check form,  NIBP Module, M-NIBP

A-1(2)

Document No. 8001015-1

SERVICE CHECK FORM

Non-Invasive Blood Pressure Module, M-NIBP

Customer

Service

Module type

S/N

Service engineer

Date

OK = Test OK

N.A. = Test not applicable

Fail = Test Failed

OK

N.A.

Fail

OK

N.A.

Fail

1.

 

Internal parts

2.

 

External parts

3.

 

Pump’s filter

4.

 

Installation

Notes

5.

 

Recognition

6.

 

Module software

NIBP

7.

 

Communication and

memories

8.

 

LEDs and membrane

keys

9.

 

Pump and valves

10.

 

Leak test

≤

 5 mmHg/min

11.

 

Calibration check

Measured B1

Measured B2

Allowed range

0 mmHg

±

10 mmHg

100 mmHg

100 + z.o. 

±

2 mmHg

200 mmHg

200 + z.o. 

±

3 mmHg

260 mmHg

260 + z.o. 

±

4 mmHg

z.o. = zero offset at 0 mmHg pressure

12.

 

Watchdog timer activation pressure

9...19 / 5...10 mmHg

Summary of Contents for S/5 M-NIBP

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands