manualshive.com logo in svg

Datex-Ohmeda D-VHC17, Technical Reference Manual

Share
Download
Datex-Ohmeda D-VHC17 Technical Reference Manual Download Page 23

Displays and Controller Boards

Document No. 8001004-1

17

11.

 

Perform electrical safety check and leakage current test.

?

12.

 

Check that the display functions normally after the performed electrical safety check.

?

13.

 

Clean the picture tube with a clean, soft cloth dampened with suitable cleaning solution.

NOTE: Do not use any abrasives or hard objects to remove stains. Do not polish the screen.

Clean the display cover with a cloth dampened with a mild detergent solvent.

NOTE: Do not use strong solvents (e.g. acetone) or aerosol cleaners for cleaning the cover.

?

•

 

Fill in all necessary documents.

3.2.2

 

Video Display, D-VNC15

Tools needed

Command Board, Central Unit, B-DISP, parameter modules

•

 

Turn the monitor to STBY.

14.

 

Check that the display cover and the picture tube screen are intact.

?

15.

 

Check that the display power cord is locked to the display with a power cord guard.

?

16.

 

Disconnect the display power cord from the power supply unit and check that the connector

pins are clean and straight. Check that the power cord is intact.

Reconnect the power cord properly.

?

17.

 

Disconnect the display video cable from the B-DISP and check that the connector pins are

clean and straight. Check that the video cable is intact. Check that the thumb screws on the

video cable connector are intact.

Reconnect the video cable and lock it properly.

?

18.

 

Turn the monitor on. Check that the power-on indicator LED on the display front panel lights

up.

?

Summary of Contents for D-VHC17









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands