Datex-Ohmeda 7100 Technical Reference Manual Download Page 104

Page: 104 / 158

7100 Anesthesia Ventilator

6-2

02/03 1006-0836-000

WARNING

Do not perform testing or maintenance on this instrument while it is
being used to ventilate a patient. Possible injury can result.

WARNING

Items can be contaminated due to infectious patients. Wear sterile
rubber gloves. Contamination can spread to you and others.

WARNING

Obey infection control and safety procedures. Used equipment may
contain blood and body fluids.

6.1 Maintenance Schedule

The 7100 Ventilator is an integral component of the Aestiva/5 7100
anesthesia machine and the S/5 Aespire anesthesia machine.

Refer to Section 5, “

Maintenance

,” in the respective anesthesia machine

Technical Reference manual for the “

Planned Maintenance Schedule

.”

Summary of Contents for 7100






























































































































































Search results

Summary of Contents for 7100

Reviews:

Brands by name

Popular brands

Datex-Ohmeda 7100, Technical Reference Manual

Search results

Summary of Contents for 7100

Reviews:

Brands by name

Popular brands