Dataradio G3 Installation Manual Download Page 7

 
 

156 90000-508 

 

  

G3

    

 Installation Guide 

 

2

DATARADIO Corp. 
6160 Peachtree Dunwoody RD., suite C-200 
Atlanta, Georgia 30328 

Technical support hours: Monday to Friday 
8:30 AM to 5:30 PM, Eastern Time 

phone:  1 770 392-0002 
fax: 

1 770 392-9199 

Email address: 

[email protected]

 

1.4 Product 

Warranty 

Warranty information may be obtained by 
contacting your sales representative. 

1.5 Replacement 

Parts 

This product is not field serviceable, except 
by the replacement of a complete unit. Spe-
cialized equipment and training is required 
to repair the GCU board and radio modules. 

Contact Technical Support for service in-
formation before returning equipment. A 
Technical Support representative may sug-
gest a solution eliminating the need to return 
equipment. 

1.5.1 Factory Repair 

When returning equipment for repair, you 
must request an RMA (Returned Material 
Authorization) number. The Tech Support 
representative will ask you several questions 
to clearly identify the problem. Please give 
the representative the name of a contact per-
son who is familiar with the problem, should 
questions arise during servicing of the unit. 

Customers are responsible for shipping 
charges for returned units. Units in warranty 
will be repaired free of charge unless there is 
evidence of abuse or damage beyond the 
terms of the warranty. Units out of warranty 
will be subject to service charges. Informa-
tion about these charges is available from 
Technical Support. 

1.6 Unpacking 

When ready for installation, carefully un-
pack your  G3

    

 kit shipping carton and 

identify each item as listed below: 

 

One  G3

    

 

 

Installation mounting bracket  

 

Power cable – 22 feet (6.7 meters) 

 

Small parts kit 

If damage has occurred to the equipment 
during shipment, file a claim with the carrier 
immediately. 
 

Summary of Contents for G3





















Reviews: