Datalogic Memor™ Single Ethernet Cradle
NOTE
Read this manual carefully before performing any type
of connection through the Datalogic Memor™ Single
Ethernet Cradle.
The user is responsible for any damages caused by
incorrect use of the equipment or by inobservance of the
indication supplied in this manual.
NOTE
Do not attempt to disassemble the Datalogic Memor™
Single Ethernet Cradle, as it does not contain parts that
can be repaired by the user. Any tampering will invalidate
the warranty.
The Datalogic Memor™ Single Ethernet Cradle paired with one Datalogic
Memor™ mobile computer builds a reading system for the collection,
decoding and transmission of barcoded data.
The communication between the mobile computer and host PC through
the Datalogic Memor™ Single Ethernet Cradle may occur also by using
the standard ActiveSync® connection.
Figure 1 – Datalogic Memor™ Single Ethernet Cradle
A) LED
Indicators
B)
Spare Battery Slot
C)
Mini USB Connector
D) RS232
Connector
E) Power
Jack
F)
Ethernet Port with LED indicators
G) Switch
Ethernet/USB
The Datalogic Memor™ Single Ethernet Cradle is a serial
communication adapter between the host computer and the Datalogic
Memor™ mobile computer. Power supply is required to be connected to
the Cradle only for ethernet communication.
Since the Datalogic Memor™ Single Ethernet Cradle also functions as a
battery charger, a power supply is required for battery recharging
operations, both for the mobile computer and spare battery pack
recharging. The spare battery pack recharging slot can supply a 1000
mAh as well as a 2000 mAh Battery pac.
822000820
By inserting the Datalogic Memor™ into the cradle, data can be
transmitted to the host and its battery begins charging if the power supply
is connected. In addition, a spare battery can be charged by inserting it
into the slot at the back of the Datalogic Memor™ Single Ethernet Cradle
as shown in the following figure.
Figure 2 – Datalogic Memor™ Single Ethernet Cradle Charging and
Communication
The LEDs positioned on the front part of the Datalogic Memor™
Ethernet Cradle (see figure below) indicate the cradle and spare
battery charger status:
Figure 3 - LED Indicators
Front LED indicators
LED STATUS
Red Constant
Spare battery charging*
Charger
Green
Constant
Spare battery charge
completed
Power
Green
it is constant when the
cradle is powered
*
During charging, the LED may turn off to indicate a temporary
suspension of charging.
Ethernet Connector LED Indicators
Solid Green
Link established
Flashing Green
Link activity
Ethernet
Green LED
(left)
Off
No link established
Off
10 Mb connection
Ethernet
Yellow LED
(right)
Solid Yellow
100 Mb connection (this model is not
available)
CONNECTIONS
CAUTION
Connections should always be made with power OFF!
USB CONNECTION
The Datalogic Memor™ Single Ethernet Cradle can be connected to the
host by means of any standard Mini USB cable.
Once the host has been turned on, insert the Datalogic Memor™
mobile computer into the cradle.
Figure 4 - USB Connection
A) Host
Computer
C) Datalogic Memor™ Single
Ethernet Cradle
B) Std Mini USB (i.e.
94A051016 CAB-421)
D) *Power Supply (only necessary
for battery charging)
* Recommended power supply: 94ACC1324 PG5-30P35 AC/DC
POWER SUPPLY EU/USA PLUG.
NOTE
Be sure that the switch is in the “USB” position.
During switch operation from USB position to Ethernet
position and vice versa the mobile computer must not be
inserted in the cradle.
Spare battery
Charge Slot with
Spare Battery
Inserted
Data Transmission and
Mobile Computer Battery
Charging
Spare Battery
Charger LED
Power LED
A
B
C
D*
A
B
C
D
F
G
E
