Datalogic Magellan 800i Reference Manual Download

Page: 95 / 184

Code 39

Product Reference Guide

Code 39

The following options apply to the Code 39 symbology.

Disable/Enable Code 39

When this feature is disabled, the scanner will not read Code 39 bar codes.

Check Character Calculation

When enabled, the scanner will calculate the check character of the labels. Turn this option on
only when a checksum is present in the Code 39 labels. When disabled, any check character in
the label is treated as a data character

START / END

PROGRAMMING BAR CODES

Disable Code 39

Enable Code 39

DEFAULT

008E00(CR)

008E01(CR)

START / END

PROGRAMMING BAR CODES

Disable Check Char Calculation

DEFAULT

Enable Check Char Calculation

005500(CR)

005501(CR)

Summary of Contents for Magellan 800i

























































































































































































Search results

Summary of Contents for Magellan 800i

Reviews:

Related manuals for Magellan 800i

Brands by name

Popular brands

Datalogic Magellan 800i, Reference Manual

Search results

Summary of Contents for Magellan 800i

Reviews:

Related manuals for Magellan 800i

Brands by name

Popular brands