DataVS2 - VSM
Vision Sensor Monitor
QUICK REFERENCE GUIDE
DESCRIPTION
The VSM is an external monitor compatible with all the vision sensors of the
DataVS2 series. The device displays images, results and statistics of the
check carried-out on the sensor as well as the fine tuning of the configuration
parameters.
-
Monitor with 3.5” colour LCD display;
-
Operator interface with 8 push-buttons
and 8 signalling LEDs;
-
Compatibility with the entire DataVS2
series;
-
Image and statistics visualisation;
-
Configuration parameter modification;
-
Memorisation of 20 different inspections;
-
Different user profiles management
through passwords.
FEATURES
VSM MONITOR
The VSM displays the images processed by the DataVS2, manages
inspections and carries-out the parameter fine tuning.
1. Monitor
2. Status
LEDs
3. STATUS
Button
4. TEACH
Button
5. Power
Supply
Connector
6. ARROW
Buttons
7. Ethernet
Network
Connector
8. ESC
Button
9. SET
Button
10. Power,
OUT,
ETH
Link LEDs
SIGNALLING LEDS
From left to right
1.
Setup Mode, green;
2.
Adjust Mode, green;
3.
Monitor Mode, green;
4.
Main Menu, green;
5.
Power Supply, green;
6.
Digital Output 1, yellow;
7.
Digital Output 2, yellow;
8.
Connection Status, green.
1 2 3 4 5 6 7 8
ELECTRICAL CONNECTIONS
3
1
2
4
3
1
2
4
M12 4-Pin Male
(Power Supply)
pin 1:
+24 Vdc
pin 2:
Reserved
pin 3:
GROUND
pin 4:
Reserved
M12 Reverse Keyed 4-Pin Male
(Ethernet Network)
pin 1:
Ethernet
RX+
pin 2:
Ethernet
TX+
pin 3:
Ethernet
RX-
pin 4:
Ethernet
TX-
The VSM monitor can be connected in a LAN network using a straight
Ethernet cable or can be connected using a point to point connection directly
to a vision sensor.
LAN CONNECTION
POINT-TO-POINT CONNECTION
GROUND CONNECTION
To comply with the EMC requirements, the Ethernet cable shield has to be
grounded. (Use the yellow/green cable supplied with the VSM).
Insert the washer M12 on the yellow/green cable in the VSM connector and
then screw the Ethernet cable until the ring nut reaches the washer.
Warnings
Insert the cable into the correct connector following the key
indications inside the body
After inserting the cable, turn the ring nut anticlockwise to ensure
connection
Never force the cable inside the connectors.
Make sure that every cable is connected to the right connector
Before disconnecting the cable, completely turn the ring nut
anticlockwise
VSM MOUNTING
All the accessories for VSM mounting are included in the package. The VSM
unit can be installed on a DIN rail or on a panel.
DIN RAIL MOUNTING
Wedge the VSM unit in the DIN rail. First set the upper part of the monitor and
then press down the lower part.
Once inserted, block the VSM monitor using the two white side locking clips.
PANEL MOUNTING
Place the rubber seal around the monitor body.
Then fix the monitor on the panel using the two locking screws and the two
rubber caps.
92
±0.2
[3.62
±0.01
]
92
±0
.2
[3.62
±0
.0
1
]
R7.5
[R0.30]
Panel Cutout
TECHNICAL DATA
Supply Voltage:
24 Vdc ± 10%
Ripple Voltage:
2.4 Vpp max
Current Draw:
Max 150 mA @ 24 Vdc
Dimensions:
96 x 96 x 39 mm
Indicators:
8 LEDs + 3.5’’ LCD color display
Setup: DataVS2
GUI
Data Retention:
non volatile FLASH memory
Operating Temperature:
-10 °C … +55 °C
Storage Temperature:
-20 °C … +70 °C
Vibrations:
(EN60068-2-6)
14 mm @ 2 to 10 Hz;
1.5 mm @ 13 to 55 Hz;
2 g @ 70 to 200 Hz; 2 hours on each axis
Shock Resistance:
(EN60068-2-27)
11 ms (30 G) 6 shocks on each axis
Housing Material:
ABS
Mechanical Protection:
IP20 (IP40 when panel mounted)
Connections:
2 x M12 4-pin
Weight: 180
g
OVERALL DIMENSIONS
96
[3.78]
96
[3
.78]
48
.0
[1
.8
9]
93
.4
[3
.6
8]
104
[4
.09]
45.0
[1.77]
90.2
[3.55]
14
.5
[0
.5
7
]
96
[3.78]
42
.5
[1
.6
7]
14.0
[0.55]
Locking Clips
Locking
Screws
Cap
Rubber Seal
LAN
Power
Powe
r
DATAVS-CV-RJ45D-03
Power
Power
Power
DATAVS-CV-VSM-xx
Powe
r
Washer M12
Ring Nut
