DataApex Colibrick Manual Download Page 5

Page: 5 / 44

Colibrick A/D Converter

1 Colibrick acquisition device

1 Colibrick acquisition device

This manual describes the use of the

Colibrick A/D Converter

with the

Clarity

software ver.

4.0 and newer

Colibrick

is an external 24-bit A/D converter that measures the voltages of

chromatographic and electrochemical detectors. It is designed for
acquisition of data from any chromatograph for the

Clarity

station.

Colibrick

uses the

USB

communication channel and thus is directly

powered from the

. The unit can be connected or disconnected anytime

without the need to switch the computer off.

Fig 1: Colibrick A/D Converter

Brief technical overview

1, 2 or 4 data acquisition channels completely independent and isolated
from the USB ground.

4 digital inputs with status indication by LED.

8 digital outputs, 4 of them also designed as relay contacts, each has its
status indicated by LED.

USB interface.

Excellent reliability and temperature stability.

- 1 -

Summary of Contents for Colibrick













































Search results

Summary of Contents for Colibrick

Reviews:

Related manuals for Colibrick

Brands by name

Popular brands

DataApex Colibrick, Manual

Search results

Summary of Contents for Colibrick

Reviews:

Related manuals for Colibrick

Brands by name

Popular brands