DataApex Colibrick Manual Download Page 37

Page: 37 / 44

5 Troubleshooting

Clarity Hardware

5.2.2.3 Reinstallation of drivers using the System Restore Point

Use the

System Restore Point

MS Windows XP/Vista/7/8

to uninstall

the incorrect drivers.

Go to

Start

–

Programs

–

Accessories

–

System Tools

–

System Restore

Windows XP or click the

Windows

key on your keyboard and type "System

Restore", then click on the found item in Windows Vista/7/8.

In the

System Restore

dialog use the

Restore my computer to an earlier

time

in Windows XP or

Choose a different restore point

in Vista/7/8 option

and press the

Next

button.

In the next dialog select a restore point from a time before the incorrect
driver was installed.

Caution:

Any software or hardware that was installed after the moment of the
selected restore point will be removed from your system.

Reinstall

Clarity

and then restart the PC.

Windows

should now correctly identify and install the drivers.

- 33 -

Summary of Contents for Colibrick













































Search results

Summary of Contents for Colibrick

Reviews:

Related manuals for Colibrick

Brands by name

Popular brands

DataApex Colibrick, Manual

Search results

Summary of Contents for Colibrick

Reviews:

Related manuals for Colibrick

Brands by name

Popular brands