manualshive.com logo in svg

Data-Tronix DT-ATSC-IP-8, User Manual & Installation Manual, Page: 7 / 15

Share
Download
Data-Tronix DT-ATSC-IP-8 User Manual & Installation Manual Download Page 7

 

NACE: 

610-429-1511 

| [email protected] | www.datatronix.biz | | DT-ATSC-IP-8 Manual v1.0    

Page 7

 

 

Device Programming and Setup via GUI Interface

 

Connecting to the GUI Interface

 

Factory Default IP: 192.168.1.9

 

 

◊

 

Connect an Ethernet cable directly (

no Cross Over cable required

) to the UTILITY Port on the rear panel of the 

encoder or connect the Ethernet cable to an Ethernet switch. Connect an Ethernet Cable to your PC/Laptop.

 

◊

 

Modify your PC/Laptop IP address to 192.168.1.11.

 

◊

 

Enter ‘192.168.1.9’ into your web browser.

 

◊

 

Enter GUI and make required device changes.

 

◊

 

Save all changes as required, upload and reboot changes.

 

◊

 

Verify parameters then end web session. 

 

Overview Page

 

 

Overview Page will provide an overall system status of the DT-ATSC-IP-8 Converter state: Signal Strength and Signal 

Quality.

 

System Parsing / Response Time:

 

The initial System Parsing time will range from 3-4 minutes on average as the system identifies and  

populates the required parameters. 

As the user navigates the device's menu note that a small delay may occur in populating the data on the screen as the 

system is constantly performing system parsing and system housekeeping functions.

 

Summary of Contents for DT-ATSC-IP-8
















Reviews:

No comments