manualshive.com logo in svg

Data Translation DT9840 Series, User Manual

Share
Download
Data Translation DT9840 Series User Manual Download Page 50

Chapter 2

50

31

Indicates where the clock and trigger 
signals come from. This bit is controlled 
by the DSP. 

1 = The module receives all A/D and D/A clocks and 

triggers from the Scalable Bus. The internal DSP 
and counter/timers operate on  their own 
independent clock. This setting is used for slave 
modules.

0 = The module receives all A/D and D/A clocks and 

triggers from its own inputs (not from the Scalable 
Bus). This setting is typically used by the master

module only.

R/W

a.  All bits power up in the "0" state. When all the power supplies are correct, bit 0 switches to "1," indicating the module is ready 

for use. 

b.  This mode is currently not supported in software.
c.  A two-color LED (CR6 on the DT9841E module, CR1 on all other modules) is visible from the back of the module. When power 

is applied to the module, this LED turns green. When the module is recognized by the host and the firmware is downloaded to 
the module, the LED turns red. When the Windows driver is loaded and started, the LED turns orange.When you download 
and run your DSP program, this LED flashes green and orange. When you download and run your DSP program, this LED 
flashes green and orange. If the downloaded program stops running, this LED turns stops flashing (in either the green or 
orange state) to indicate that an error occurred, and the debug LEDs (CR7 to CR14) turn on. You can define the state of the 
debug LEDs using software. Three address LEDs (CR15) indicate the Scalable Bus address; position M is the master and 
positions 1 and 2 are turned on as needed to represent the slave address. The intensity of the LEDs for the addressed module is 
brighter than the LEDs for the nonaddressed modules. Debug and Address LEDs are not supported on the DT9841E.

d.  This bit is set if the data in the input latch has not been updated on the next D/A clock. At the fastest clock rate, this means that 

the data must be updated within 10 

μ

s. 

e.  This bit will be set if the A/D clock is faster than the A/D converter specification or if the data was not read fast enough by the 

DSP or host. 

Table 5: Hardware Control and Status Register (Address 0xB0000000)

 

 (cont.)

Bit

Register Description

Value

a

Type

Summary of Contents for DT9840 Series



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands