Data Translation DT9816 Series User Manual Download Page 73

Page: 73 / 108

Supported Device Driver Capabilities

Channels

Gain

Table 11: Channel Options

DT9816 Series

A/D

D/A

DIN

DOUT

C/T

TACH

QUAD

Number of Channels

NumberOfChannels

a. The DT9816 Series provides analog input channels 0 to 5.

1 1 1

SE Support

SupportsSingleEnded

Yes

SE Channels

MaxSingleEndedChannels

DI Support

SupportsDifferential

Yes

DI Channels

MaxDifferentialChannels

Maximum Channel-Gain List Depth

CGLDepth

b. You cannot specify the same channel more than once in the list. Place channels in your channel list in

ascending order. All channels are sampled simultaneously with data returned in ascending channel
order; if your channel does not match, you will have unexpected results.

0 0 0

Simultaneous Sample-and-Hold Support

SupportsSimultaneousSampleHold

Yes

Channel-List Inhibit

SupportsChannelListInhibit

Support MultiSensor Inputs

SupportsMultiSensor

Bias Return Termination Resistor Support

SupportsInputTermination

Table 12: Gain Options

DT9816 Series

A/D

D/A

DIN

DOUT

C/T

TACH

QUAD

Programmable Gain Support

SupportsProgrammableGain

Yes

Number of Gains

NumberOfSupportedGains

Gains Available

SupportedGains

1, 2

a. A gain of 1 sets the effective input range to ±10 V; a gain of 2 sets the effective input range to ±5 V. You

must set the gain to the same value for all channels, even if you are using a subset of the channels.

Summary of Contents for DT9816 Series













































































































Search results

Summary of Contents for DT9816 Series

Reviews:

Brands by name

Popular brands

Data Translation DT9816 Series, User Manual

Search results

Summary of Contents for DT9816 Series

Reviews:

Brands by name

Popular brands