Data Translation DT3145 Getting Started Manual Download Page 5 | Manualshive

Page: 5 / 60

background image

v

About this Manual

This manual describes how to get started using a DT3145 frame
grabber board.

Intended Audience

This document is intended for engineers, scientists, technicians, or
others responsible for setting up a DT3145 board to perform machine
vision and/or image analysis operations. It is assumed that you are
familiar with the Windows® 2000 or Windows XP operating
environment on the IBM



PC or compatible computer platform and

with the operating characteristics of your Camera Link camera.

What You Should Learn from this Manual

This manual will help you install and set up your board and required
software successfully. It is organized as follows:

•

“Overview,”

describes the key features of the DT3145

hardware and software, and provides an overview of the getting
started procedure.

•

“Preparing to Use the DT3145,”

describes how to

unpack the board and software, check system requirements,
install the DT3145 software, and view the DT3145 documentation
online.

•

“Installing the Board and Configuring the Device

describes how to install the DT3145 board and configure

the device driver in Windows 2000 and Windows XP.

•

“Connecting Signals,”

describes how to connect the

camera to the board and how to connect signals to the board.

•

“Verifying Board Operation,”

describes how to verify

the board’s operation using DT-AcquireCL.

«
...
3
4
5
6
7
...
»

Summary of Contents for DT3145





























































Reviews:

No comments

Related manuals for DT3145

Brand: GE Pages: 146

Brand: Vonets Pages: 8

EK-FB GA AX370 Gaming RGB Monoblock

Brand: ekwb Pages: 2

Brand: Alesis Pages: 46

Urban Wireless CC-VT240W

Brand: Cateye Pages: 15

Brand: Keithley Pages: 71

kontron KBox E-420-R1K/V1K

Brand: S&T Pages: 82

Brand: ZALMAN Pages: 11

Brand: Cameo Pages: 23

Brand: SSV Embedded Systems Pages: 17

Brand: Aaeon Pages: 72

PFC Chokes PFC3515V Series

Brand: Delta Electronics Pages: 1

Brand: Magma Pages: 2

Brand: Cypress Semiconductor Pages: 15

Brand: Icy Box Pages: 2

Brand: M-system Pages: 4

Brand: Intel Pages: 54

Brand: IBM Pages: 74

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands