3
10
11
Ingresso pulsante pedonale, apre parzialmente il
cancello(per circa 7 sec.) contatto N.O.
20
21
Uscita 24Vac per alimentare i dispositivi esterni come le
fotocellule
10
12
Ingresso pulsante START se premuto durante la
fase di apertura ferma la manovra,durante la
chiusura inverte il movimento.Contatto N.O.
22
23
Uscita spia cancello aperto(22=+24Vdc 23=gnd massimo
30mA) segue il funzionamento del led DL1
10
13
Ingresso pulsante STOP se premuto ferma
qualunque manovra e annulla la richiusura
automaticaContatto N.C.
24
25
Ingresso antenna collegare al morsetto 25 il polo caldo
dell’antenna e al morsetto 24 la calza dell’antenna
26
27
Uscita secondo canale radio, contatto N.O. pulito (portata, vedi caratteristiche del ricevitore)
6. Collaudo
Da eseguire con il cancello a metà della sua corsa e solo dopo aver installato tutti i dispositivi di sicurezza previsti dalle
normative vigenti al fine di ridurre al minimo ogni rischio
•
Verificare il corretto collegamento del motore tenendo presente che la prima manovra che la scheda esegue una volta alimentata
è un apertura se questo non avviene invertire i collegamenti ai morsetti 6-7
•
Verificare il corretto funzionamento dei finecorsa movendo manualmente la leva e controllando che si spenga il led corrispondente
in caso contrario invertire i collegamenti ai morsetti 17-18
•
Verificare il corretto funzionamento di tutti i dispositivi di sicurezza installati al fine di ridurre al minimo ogni eventuale rischio.
•
Istruire il personale addetto all’uso dell’automazione sui relativi comandi, dispositivi di sicurezza e pericolosità derivante dall’uso
dell’automazione.
•
Compilare il fascicolo tecnico ed adempiere agli eventuali obblighi derivanti dalle normative vigenti.
GB
1. Safety
rules
Warning:
Any repairing, fitting or adjustment made from people not qualified is strictly forbidden and in order to avoid any possible
accident, all necessary precautions must been taken (ex: switch off the power supply as well as disconnect batteries). Daspi is not
responsible for possible damages or injuries to people, objects or animals caused by any unauthorized modification of product. Do not
install this product into an explosive place
Keep scrupulously this booklet and include it into the main user manual in a suitable place well known by all the interested people.
2. Model
The control panel MACH6E has been designed for driving
1 operator
for sliding gates mod. BIG FOOT and it has an electric clutch
and electronic brake. Daspi is not responsible for any different use of control panel MACH6E
3. Main
components
F1
Power supply fuse10A
JP1
Terminal for power supply connection 230 Vca 50 Hz
F2
Control fuse 2A
JP2
Terminal for connecting the motor, the light and 2° capacitor
F3
Flashing light fuse 2A
JP3
Terminal for connecting the safety and control devices
SW1
Dip-switch for the control panel programming
J1
Radio receiver connector
Led showing the control panel’s connections (to be checked after turning on the power supply)
DL1
It shows the manoeuvre of the gate (1 flashing/sec. while opening, fix light with the gate completely open, 2 flashing/sec. while
closing)
DL2
Always off, it turns on with control PED(pedestrian)
DL5
Always on, it turns off with control PHOTOCELLS
DL3
Always off, it turns on with control START
DL6
Always on, it turns off with control SEFETY DEVICE
DL4
Always on, it turns off with control STOP
DL7
Always on, it turns off with control LIMIT SWITCH OPENING
DL8
Always on, it turns off with control LIMIT SWITCH CLOSING
Check again the connections and the devices if the above led don’t correspond.
4. Control panel programming and set up
The programming of dip switches must be made with control panel switched off
SW1 ON
OFF
1
It sets the automatic shutting, adjustable by trimmer BREAK
Automatic shutting off.
2
It doesn’t accept any other control START while opening
(residential system)
Control START is accepted while the gate is opening. Gate
stops.
3
Pre-flashing of 2 seconds before any movement
Pre-flashing off
4
It sets the feature “close immediately” (trimmer BREAK
must
be
more than 0) working only while opening.
With the dip residential system ON, if photocells detect
something , as soon as the gate open completely it closes
immediately, only if the photocells are freed.
With the dip residential system OFF, if photocells detect
something , as soon as the entrance is freed, the gate starts
closing after 2 seconds.
“Close immediately” off
5
Separate entrances OPEN - CLOSE:
the entrance START becomes OPEN and the entrance PED
(pedestrian) becomes CLOSE.
Normal working
6
Photocells working while opening. As soon as they are freed,
the gate keep opening.
Photocells working only while closing. If they detect
something, the gate stops and re-opens.