manualshive.com logo in svg

DANPHONE Futronic MKII, User Manual

Share
Download
DANPHONE Futronic MKII User Manual Download Page 28

 

Page 28 of 65 

 

 

The SPACE and the MARK frequencies are measured during the initial part of the DSC call. 
The measurements are done by means of a time measurement on an AF signal (1700 Hz +/- 85 
Hz) derived from the MF/HF MARK/SPACE signal.  
 
The time measurements for MARK and SPACE respectively are converted to frequency and the 
calculated values are added to an offset frequency for the actual MF/HF frequency. By adding 
the offset frequency to the measured/calculated frequencies the actual MF/HF MARK/SPACE 
frequencies are obtained. 
 
The AF signal used for calculation of the MARK/SPACE frequencies must be within 1615 +/-15 
Hz and 1785 +/-15 Hz respectively to be accepted. 
 

Simultaneous MF/HF power test 

 
When the MH/HF Power Sensor (optional accessory) is connected between the transmitter 
output terminal and the antenna tuner Futronic MKll will display the PEP power and VSWR. The 
test results are stored in the test box memory along with the DSC data.  

 

 
 
 
 
 
 

 
 

 

 
 
 
 

 

 

   

 

Example of Printout from the Memory: 

 

 

 

MF/HF # 1   Time/date: 08:58:01 / 04-12-2019 

 

DSC DATA:  2187.5 kHz 

 

RX MMSI: 9999999990  Format 120 Category: 100 TX MMSI: 2190155210 

 

1.telecommand: 109 2.telecommand: 126 Info.: 02 26 50 02 26 50  

 

EOS: 117 ECC: 94  Status: OK 

 

Mark: 2187428 Hz  Space: 2187592 Hz  Fwd: 264 Watt PEP  Rev: 1 Watt PEP VSWR:  1.1 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

ANT. 

MF/HF DSC TRANSMITTER 

ATU 

Summary of Contents for Futronic MKII


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands