manualshive.com logo in svg

DANPHONE Futronic MKII, User Manual

Share
Download
DANPHONE Futronic MKII User Manual Download Page 27

 

Page 27 of 65 

 

 

MF/HF Radios 

 
Set Number 
 
As you may wish to test several radios under the same MMSI, each radio can be given its own 
individual set number for recognition. Default number is 1. Press 

“OK”

 to confirm or press 

↑ or ↓

 

  

to change to another number. Then, press 

“OK”

 and go to the test you wish to perform.  

 

 

Receive DSC 

 
In the Receive DSC test mode, the test box will receive the radio’s MMSI number and DSC data 
transmitted, and at the same time measure the frequency of the transmission.  
 
Connect the wire antenna supplied with the test box and use the setup below. The test box 
antenna should be able to “see” the transmitter’s antenna. 
 
 
 
 
 
 
 
 
 
 

 

 
Select 

“Receive DSC”

 and press 

“OK”

. Then select whether the test box is going to receive 

the call on one of the 

“TFC” 

channels or 

“MF/HF” 

distress channels. Press 

“OK”

 and select 

frequency. Finally, press 

“OK”

 again and activate the transmitter.  

 
The test box remains in receive mode until a DSC call is received. A press on the EXIT button 
can interrupt the mode, provided that the test box has not started to receive a call, in which case 
you have to wait for a few seconds. MMSI number, data and the MARK/SPACE frequencies are 
presented in the display and stored in memory, provided that the checksum is OK.  
 
Test results are displayed line by line. Press 

↑ or ↓ to toggle between the lines.  

 
If the MARK/SPACE frequencies do not appear on the LCD display, the signal is most likely 
outside the limits 1770-1800 Hz / 1600-1630 Hz, or the signal was unstable during the header 
or that the header was too short (less than 11 bit). If data are shown as 255, it's because they 
were received in error. 
 
 

    Example of Printout from the Memory: 

    

MF/HF # 1   Time/date: 08:56:20 / 04-12-2019 
DSC DATA:  2187.5 kHz 
RX MMSI: 9999999990  Format 120 Category: 100 TX MMSI: 2190155210 
1.telecommand: 109 2.telecommand: 126 Info.: 02 26 50 02 26 50  
EOS: 117 ECC: 94  Status: OK 
Mark: 2187428 Hz  Space: 2187592 Hz 

ANT. 

MF/HF DSC TRANSMITTER 

Summary of Contents for Futronic MKII


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands