manualshive.com logo in svg

DANPHONE Futronic MKII, User Manual

Share
Download
DANPHONE Futronic MKII User Manual Download Page 23

 

Page 23 of 65 

 

 

FM Deviation 

 
There are 3 types of audio reference devices: 

Model no.: 152.4002.001/152.4002.002

 

– single tone (1kHz) 

Model no.: 152.4002.003

 

– with three tone frequencies (1 kHz, 2 kHz, 500 Hz) and two volume 

levels.  

Model no.: 152.4002.004

 

– with four tone frequencies (multi tone 1+2 kHz, 1 kHz, 2 kHz and 

500 Hz) and two volume levels. 
 
 
   On/off 

 

               Selector   

   switch 

 

               Long press: Change frequency 

 

 

               Short press: Change volume 

 
 
 
 
 
The illustration below shows how to set up for measuring  
the VHF FM Deviation on CH 6, 8, 9, 13 or 16: 
 
 
 
 
 
 
 
 
 
 
The test procedure is as follows: 
 
1) Select 

“FM Deviation”.

 

2) Select between CH 6, 8, 9, 13 or 16 with the up/down buttons and press Ok. 
3) Hold the audio reference device / AF generator close to the transmitter’s microphone 
     and activate the tone,  
4) Activate the transmitter on selected channel  
5) Press 

“OK”

 on the test box. Maximum deviation and actual deviation are shown on the LCD 

    display, 
6) Press 

“OK”

 on the test box, and the maximum deviation value will be stored in the memory, 

7) Stop the transmitter. 
 
 

    Example of Printout from the Memory: 

     
    VHF # 1   Time/date: 08:54:38 / 26-11-2019  
    CH08-156.400 MHz Maximum deviation:  3.6 kHz  
  
    VHF # 1   Time/date: 08:54:51 / 26-11-2019  
    CH06-156.300 MHz Maximum deviation:  3.6 kHz

 

 

VHF TRANSMITTER 

AUDIO 
REFERENCE  

ANT. 

Summary of Contents for Futronic MKII


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands