manualshive.com logo in svg

Danfoss VLT Soft Starter MCD 600, Installation Manual, Page: 9 / 34

Share
Download
Danfoss VLT Soft Starter MCD 600 Installation Manual Download Page 9

•

•
•

4 Device Configuration

4.1 Before Configuring the Device

N O T I C E

The error LED flashes whenever the device is receiving power but is not connected to a network. The error LED will flash occa-
sionally during the configuration process.

N O T I C E

At power-up, the communication card loads the IP address stored in the soft starter.

4.2 Configuration Methods

Network communication parameters for the communication card can be set via the soft starter or via the on-board web server.

The card uses a static IP address by default. To enable DHCP addressing, set 

parameter 12–20 DHCP

 to enable or change the

setting via the on-board web server.
The IP address can be set via the programmable parameters of the soft starter.
The web server can configure the IP address and messaging settings for MQTT/OPC UA operation.

4.3 Parameters for Configuring Network Settings

Use 

parameters 12-8

 to 

12-21

 to configure the network address. The parameters can be set via the Main Menu, via the Setup Tools,

or by uploading a configuration file via USB Save & Load.

Parameter

Default

12-8 Gateway Address

192

12-9 Gateway Address 2

168

12-10 Gateway Address 3

0

12-11 Gateway Address 4

100

12-12 IP Address

192

12-13 IP Address 2

168

12-14 IP Address 3

0

12-15 IP Address 4

2

12-16 Subnet Mask

255

12-17 Subnet Mask 2

255

12-18 Subnet Mask 3

255

12-19 Subnet Mask 4

0

12-20 DHCP

Disable

12-21 Location ID

0

4.4 Enabling Network Control

N O T I C E

If the reset input is active, the soft starter does not operate. If a reset switch is not required, use 

parameter 7-9

 to set the reset

input to normally open or fit a link across terminals RESET, COM+ on the soft starter.

AN353423548483en-000101 / 130R0945 | 9

Danfoss A/S © 2020.12

Device Configuration

EtherNet/IP Card

Installation Guide

Summary of Contents for VLT Soft Starter MCD 600



































Reviews:

No comments