manualshive.com logo in svg

Danfoss VLT Soft Starter MCD 600, Installation Manual, Page: 25 / 34

Share
Download
Danfoss VLT Soft Starter MCD 600 Installation Manual Download Page 25

Code

Description

121

Battery/clock

122

Thermistor circuit

124

RTD/PT100 B

133

Overpower

134

Underpower

142

LCP disconnected

143

Zero speed detect

144

SCR Itsm

145

Instantaneous overcurrent

146

Rating capacity

156

Current read error L1

157

Current read error L2

158

Current read error L3

160

Motor connection T1

161

Motor connection T2

162

Motor connection T3

163

Firing fail P1

164

Firing fail P2

165

Firing fail P3

166

VZC fail P1

167

VZC fail P2

168

VZC fail P3

169

Low control volts

170–182

Internal fault X. Contact the local supplier with the fault code (X).

8.2 Parameter Lists

N O T I C E

These parameter lists are for parameter list version 2.x. To check the parameter list version, read class 103d, instance 131, attrib-
ute 100.
For other parameter list versions, refer to the soft starter Operating Guide or contact the local supplier for assistance.

N O T I C E

The numbering of parameter options via communications starts at 0. For Phase Sequence, 0 = Any sequence, 1 = Positive only, 2
= Negative only.

AN353423548483en-000101 / 130R0945 | 25

Danfoss A/S © 2020.12

Attributes

EtherNet/IP Card

Installation Guide

Summary of Contents for VLT Soft Starter MCD 600



































Reviews:

No comments