manualshive.com logo in svg

Danfoss VLT Soft Starter MCD 600, Installation Manual, Page: 18 / 34

Share
Download
Danfoss VLT Soft Starter MCD 600 Installation Manual Download Page 18

7 Messaging

7.1 Implicit Messaging (Cyclic Operation)

This section lists the requirements related to cyclic (implicit messaging) services for the EtherNet/IP Card. The minimum cyclic inter-
val is 1 ms. All data is in little endian format.

7.1.1 Assembly Objects

Table 4: Supported Assembly Objects

Description

Class

Instance

Type

Maximum size

Output (scanner

⇒

soft starter)

04d (0x04)

104d (0x68)

Integer

2 (4 bytes)

Input (soft starter

⇒

scanner)

04d (0x04)

154d (0x9A)

Integer

6 (12 bytes)

7.1.2 Control Commands (Assembly Instance 104d)

To send control data from the scanner to the soft starter, use assembly class 04d (0x04), assembly instance 104d (0x68), attribute
03d (0x03).

7.1.2.1 Bytes 0–1: Command

Bits

Function

Details

0–5

Reserved

Must be 0.

6

Run

0 = Stop command
1 = Start command

7

Reset

Changing this bit from 0 to 1 resets a trip.

8–12

Reserved

Must be 0.

13

Motor set select

0 = Use primary motor set when starting.
1 = Use secondary motor set when starting.

14–15

Reserved

Must be 0.

7.1.2.2 Bytes 2–3: Reserved

Bits

Function

Details

0–15

Reserved

Must be 0.

7.1.2.3 Command Examples

Byte Value

Description

0

0b01000000 (64d, 0x40)

Command: Start the soft starter.

1

0b00000000 (00d, 0x00) or
0b00100000 (32d, 0x20)

Command: Select primary or secondary motor settings when starting.

0

0b10000000 (128d, 0x80)

Command: Reset the soft starter.
The reset only occurs when the previous reset bit is 0, otherwise the value of 1 is ig-
nored.

0

0b11000000 (192d, 0xC0)

Command: Reset and start the soft starter.

0

0bX0000000 (00d, 0x00)

Command: Stop the soft starter.

AN353423548483en-000101 / 130R0945

18 | Danfoss A/S © 2020.12

Messaging

EtherNet/IP Card

Installation Guide

Summary of Contents for VLT Soft Starter MCD 600



































Reviews:

No comments