Danfoss VLT Soft Starter MCD 600 Installation Manual Download Page 14 | Manualshive

Page: 14 / 34

Danfoss VLT Soft Starter MCD 600 Installation Manual Download Page 14

1.
2.
3.

4.
5.
6.

1.
2.

4.5.4.2 Configuring OPC UA Settings

e7

7h

a8

13

.1

0

Procedure

Connect to the web server and click

Configuration

.

Select

OPC UA Server

.

Tick the

Enable

checkbox to enable OPC UA client operation.

The OPC UA client is enabled by default.

Click

Server Configuration

and configure the settings as required.

Select

Actions

to select the actions for different object instances.

Click

Submit

to save all settings in the card.

4.6 Scanning the Network

If there is no connection to the web server and the soft starter cannot be accessed physically, use the Ethernet Device Configuration
Tool to scan the network and identify the device. Changes made via the Ethernet Device Configuration Tool cannot be stored per-
manently in the device and will be lost when the control power is cycled.
Download the Ethernet Device Configuration Tool from

www.danfoss.com

under the sections Services/PC-tools.

N O T I C E

If the PC has a firewall enabled, add the tool to the list of authorized programs.

4.6.1 Identifying the Device with Ethernet Device Configuration Tool

Procedure

Start the Ethernet Device Configuration Tool.
Click

Search Devices

.

AN353423548483en-000101 / 130R0945

14 | Danfoss A/S © 2020.12

Device Configuration

EtherNet/IP Card

Installation Guide

«
...
12
13
14
15
16
...
»

Summary of Contents for VLT Soft Starter MCD 600



































Reviews:

No comments