8-05 End-of-Timeout Function
Option:
Function:
Select the action after receiving a valid control
word following a timeout. This parameter is
active only when
8-04 Control Timeout Function
is set to
[7] Set-up 1
,
[8] Set-up 2
,
[9] Set-up 3
or
[10] Set-up 4
.
[0]
Hold set-
up
Retains the set-up selected in
8-04 Control
Timeout Function
and displays a warning, until
8-06 Reset Control Timeout
toggles. Then the
frequency converter resumes its original set-up.
[1]
*
Resume
set-up
Resumes the set-up active before the timeout.
8-06 Reset Control Word Timeout
This parameter is active only when
[0] Hold set-up
has been
selected in
parameter 8-05 End-of-Timeout Function
.
Option:
Function:
[0]
*
Do not reset Retains the set-up specified in
parameter 8-04 Control Word Timeout Function
,
following a control word timeout.
[1]
Do reset
Returns the frequency converter to the
original set-up following a control word
timeout. The frequency converter performs
the reset and then immediately reverts to the
[0] Do not reset
setting.
8-07 Diagnosis Trigger
Option:
Function:
Enables and controls the frequency converter
diagnosis function.
[0]
*
Disable
Extended diagnosis data are not sent even if
they appear in the frequency converter.
[1]
Trigger on
alarms
Extended diagnosis data are sent when one
or more alarms appear.
[2]
Trigger
alarm/warn.
Extended diagnosis data are sent if one or
more alarms/warnings appear.
8-10 Control Word Profile
Select the interpretation of the control and status words
corresponding to the installed fieldbus. Only the selections valid
for the fieldbus installed in slot A are visible in the LCP display.
For guidelines in selection of
[0] Frequency converter profile
and
[1] PROFIdrive profile
, refer to the
design guide
of the related
product.
For additional guidelines in the selection of
[1] PROFIdrive profile
,
[5] ODVA
and
[7] CANopen DSP 402
, see the
installation guide
for
the installed fieldbus.
Option:
Function:
[0]
*
FC profile
[1]
PROFIdrive profile
[5]
ODVA
[7]
CANopen DSP 402
8-10 Control Word Profile
Select the interpretation of the control and status words
corresponding to the installed fieldbus. Only the selections valid
for the fieldbus installed in slot A are visible in the LCP display.
For guidelines in selection of
[0] Frequency converter profile
and
[1] PROFIdrive profile
, refer to the
design guide
of the related
product.
For additional guidelines in the selection of
[1] PROFIdrive profile
,
[5] ODVA
and
[7] CANopen DSP 402
, see the
installation guide
for
the installed fieldbus.
Option:
Function:
[8]
MCO
8-50 Coasting Select
Option:
Function:
Select control of the coasting function via the
terminals (digital input) and/or via the bus.
[0]
Digital
input
Activates start command via a digital input.
[1]
Bus
Activates start command via the serial
communication port or fieldbus option.
[2]
Logic
AND
Activates start command via the fieldbus/serial
communication port, AND additionally via one
of the digital inputs.
[3]
*
Logic OR
Activates start command via the fieldbus/serial
communication port OR via one of the digital
inputs.
8-51 Quick Stop Select
Select control of the Quick Stop function via the terminals
(digital input) and/or via the bus.
Option:
Function:
[0]
Digital input
[1]
Bus
[2]
Logic AND
[3]
*
Logic OR
8-52 DC Brake Select
Option:
Function:
Select control of the DC brake via the terminals
(digital input) and/or via the fieldbus.
NOTICE
Only selection
[0] Digital input
is available
when
1-10 Motor Construction
is set to
[1]
PM non-salient SPM
.
[0] Digital
input
Activates start command via a digital input.
[1] Bus
Activates start command via the serial communi-
cation port or fieldbus option.
[2] Logic
AND
Activates start command via the fieldbus/serial
communication port, AND additionally via one of
the digital inputs.
Parameters
Programming Guide
34
Danfoss A/S © Rev. 05/2014 All rights reserved.
MG37G102
6
6
